Search found 2460 matches

by mrtn
Wed Feb 21, 2018 7:00 pm
Forum: General Chat
Topic: Advice onRoland SG300 or BN-20?
Replies: 2
Views: 18

Re: Advice onRoland SG300 or BN-20?

SG-300 all day. Not even a question. It's MUCH MUCH MUCH faster and also easier to use due to open design.
by mrtn
Wed Feb 21, 2018 11:07 am
Forum: Roland VersaWorks and other Software
Topic: Moving folders to other HDD
Replies: 3
Views: 41

Re: Moving folders to other HDD

It's easier to install the whole application to the other drive.
by mrtn
Fri Feb 16, 2018 8:33 am
Forum: Warranties & Roland Care
Topic: SC545 EX display issue
Replies: 2
Views: 94

Re: SC545 EX display issue

Check the display panel cable.
by mrtn
Wed Feb 14, 2018 11:32 pm
Forum: Hardware
Topic: BN-20 dripping ink when performing perf/contour cut
Replies: 11
Views: 369

Re: BN-20 dripping ink when performing perf/contour cut

Ink pumping (klak-klak-klak) with the print carriage slightly to the left from parking spot is normal. The vacuum pump loads up the print head with ink and drains the unnecessary drips from the capping station by offseting the head and sucking the captop dry. The dirt in question may be anywhere in ...
by mrtn
Wed Feb 14, 2018 6:04 pm
Forum: Hardware
Topic: BN-20 dripping ink when performing perf/contour cut
Replies: 11
Views: 369

Re: BN-20 dripping ink when performing perf/contour cut

No master reset please!

It's either dirt or you have installed the wiper the wrong way or wrong (felt) slot.
by mrtn
Wed Feb 14, 2018 10:13 am
Forum: Hardware
Topic: Rolans sp300
Replies: 3
Views: 56

Re: Rolans sp300

Yes.
by mrtn
Tue Feb 13, 2018 8:57 pm
Forum: Hardware
Topic: Rolans sp300
Replies: 3
Views: 56

Re: Rolans sp300

What do you mean. It won’t measure the width for setup?

If you mean when printing then set your FULL WIDTH S setting in the menu to SHEET or FULL.
by mrtn
Thu Feb 08, 2018 9:48 am
Forum: Hardware
Topic: SP-300V some areas are "cloudy" when printed
Replies: 6
Views: 171

Re: SP-300V some areas are "cloudy" when printed

As I mentioned, the middle rollers are available in wider machines. No use in 30" machines. There's no way of installing them either so don't worry about it.

Your rollers are definitely conical, every fixed exterior roller is. It's barely noticeable but very well visible.
by mrtn
Wed Feb 07, 2018 10:49 pm
Forum: Hardware
Topic: SP-300V some areas are "cloudy" when printed
Replies: 6
Views: 171

Re: SP-300V some areas are "cloudy" when printed

I was asking you to turn off the heaters to prevent media from expanding due to heat and lifting up from the media (as it’s got nowhere to go width wise). Your 100% full suction helping also correlates with this as the media is forced to the bed. Pinch rollers can be an issue if installed the wrong ...
by mrtn
Wed Feb 07, 2018 2:00 pm
Forum: Hardware
Topic: SP-300V some areas are "cloudy" when printed
Replies: 6
Views: 171

Re: SP-300V some areas are "cloudy" when printed

Turn heaters off and see if anything changes.

Have you by any means changed the pinch rollers yourself?