Search found 2423 matches

by mrtn
Tue Jan 23, 2018 11:57 pm
Forum: Hardware
Topic: LEF 300 Firmware Update 1.8
Replies: 3
Views: 5

Re: LEF 300 Firmware Update 1.8

The update does not address this issue.

Hope your tech figures it out.
by mrtn
Tue Jan 23, 2018 11:24 pm
Forum: Hardware
Topic: LEF 300 Firmware Update 1.8
Replies: 3
Views: 5

Re: LEF 300 Firmware Update 1.8

A few rare logic errors have been fixed. Nothing critical so you don't exactly need to upgrade right now if you don't feel like it.
by mrtn
Tue Jan 23, 2018 12:13 am
Forum: Hardware
Topic: Registration Marks For Cutting Not Recognised - Roland VP540i
Replies: 3
Views: 27

Re: Registration Marks For Cutting Not Recognised - Roland VP540i

Yes, that's not necessary as the carriage moves out of the capping station and begins to look towards the left side. It will hit the first mark right away if it's lined up.
by mrtn
Mon Jan 22, 2018 10:45 pm
Forum: Hardware
Topic: Registration Marks For Cutting Not Recognised - Roland VP540i
Replies: 3
Views: 27

Re: Registration Marks For Cutting Not Recognised - Roland VP540i

Don’t move the base point with the carriage out of the capping position. The base point should only be set in feed direction. So: make sure the page width is sufficient move the media in feed direction until the rectangle lines up with the cutting strip set the base point Do not use “Center on media...
by mrtn
Sun Jan 21, 2018 12:08 pm
Forum: Roland VersaWorks and other Software
Topic: BN-20 Driver issue on windows 8
Replies: 6
Views: 68

Re: BN-20 Driver issue on windows 8

Works both in USB2 and USB3 ports. There’s something wrong with your port driver.

Windows 8 is not supported by anyone anymore, including Microsoft. Upgrade to 10 and be done with it.
by mrtn
Sun Jan 21, 2018 12:06 am
Forum: General Chat
Topic: Problem with Lef 20
Replies: 1
Views: 42

Re: Problem with Lef 20

Your captop may be stuck.
by mrtn
Sat Jan 20, 2018 2:27 pm
Forum: General Chat
Topic: eco solmax ink chip
Replies: 1
Views: 25

Re: eco solmax ink chip

They’re okay but report the cartridge to be empty. So yes, you can reuse them for third party ink cartridges.
by mrtn
Fri Jan 19, 2018 11:09 pm
Forum: Hardware
Topic: Versa Camm not printing colour...
Replies: 6
Views: 35

Re: Versa Camm not printing colour...

Yes. The loose end needs to be connected to the captop. Cut 5 mm off the end and reconnect the tube to the bottom connector of the captop.

What is the red part in the picture?

Good news is that you didn't waste any ink doing the powerful cleanings.
by mrtn
Fri Jan 19, 2018 3:46 pm
Forum: Hardware
Topic: Versa Camm not printing colour...
Replies: 2
Views: 23

Re: Versa Camm not printing colour...

PhillyDee wrote:
Fri Jan 19, 2018 9:53 am
No doubt someone will ask when the captops were last changed
I think I just did in the clone thread. Is that bad?
by mrtn
Fri Jan 19, 2018 3:42 pm
Forum: Hardware
Topic: Versa Camm not printing colour...
Replies: 6
Views: 35

Re: Versa Camm not printing colour...

Sweet Jesus.

NEVER do powerful cleanings. If two medium cleanings won't do it the problem is elsewhere and it's out of your own expertise.

Have you had the machine serviced per schedule? Captops from Digiprintsupplies don't count.