Page 1 of 2

EGX-20 Table Issue

Posted: Fri Oct 06, 2017 10:27 pm
by antelopeslr5000
Hi all,

I've just purchased a EGX-20 engraver and when I first apply power, the table moves downwards but doesn't stop, it seems as it wants to keep on moving downwards beyond its physical limit. After reaching this point, it stops driving after a few seconds and I have no control any of the X, Y and Z axis and the origin and view buttons do not work either.

I've used a EXG-20 before (I have access to one a work which I've used plenty of times) and never seen it do this.

Is this a common problem that can be fixed with a hard reset of some sort, or does it seem more terminal? I hope not because I've paid a fair bit of money for this and the guy I've purchased it from hasn't responded to any of my emails.

Any help would be greatly appreciated.

Thanks in advance!

Re: EGX-20 Table Issue

Posted: Sat Oct 07, 2017 12:42 pm
by mrtn
The problem is probably a simple case of a bad limit switch and is a (relatively) cheap repair.

As the seller ignores you it's very likely that he was out for a deliberate scam and depending on the marketplace you may/should report it. And/or give a call to your local Roland office/service provider and be done with it.

Re: EGX-20 Table Issue

Posted: Sun Oct 08, 2017 3:25 am
by antelopeslr5000
Thanks for the reply.

I've had just checked the Y axis limit switch, 10.9k ohms when open and the switch closes (0 ohms) when the table passes over it so the Y axis limit switch seems fine. I'd like to give the seller the benefit of the doubt, but since they have failed to respond to any of my emails I'm thinking maybe it was defective when sold or since it wasn't packed very well (the top clear cover over the spindle was broken as well as one of the brass hex standoffs for the cover) it may have been damaged during shipping.

I shutter to think what Roland would change to service/repair the engraver! Might be a non-economical repair.

Re: EGX-20 Table Issue

Posted: Sun Oct 08, 2017 5:47 am
by antelopeslr5000
So I've had a bit more of a look and I think I may have found the problem.

The Y axis seems fine now, I removed the belt drive and manually moved the table down over the limit switch and the stepper motor now stops. However, the X axis has an issue. The spindle moves along the X axis for a short time and then stops/jambs. So I removed the X axis stepper motor to inspect. It seems to rotate freely, doesn't feel like it's the cause of the problem. Next, I inspected the X axis gear drive (the black gearbox the stepper motor is directly connected to) and noted that two consecutive teeth of the plastic gear drive/cog is broken. This is what is causing the jam along the X axis.

So I guess now I need to identify the part number of the gear drive so I can order a replacement part though Roland. Does anyone on the forum have access to an illustrated parts breakdown for the EGX-20 engraver or a least could point me in the right direction? Any help would be greatly appreciated.

Re: EGX-20 Table Issue

Posted: Sun Oct 08, 2017 8:47 am
by mrtn
Please post a photo of the specific gear.

Re: EGX-20 Table Issue

Posted: Sun Oct 08, 2017 11:23 am
by antelopeslr5000
IMG_2676.jpg
Gear Drive Pic I
IMG_2677.jpg
Gear Drive Pic II
IMG_2683.jpg
Broken Gear Drive

Re: EGX-20 Table Issue

Posted: Sun Oct 08, 2017 11:33 am
by mrtn
Figured so. It's not in the parts list, I hope Roland people (Kai?) chime in.

Re: EGX-20 Table Issue

Posted: Wed Oct 11, 2017 11:09 am
by antelopeslr5000
I pulled the gear drive apart today to have a better look.

The black cover has a part number (COVER, GEAR 22025615).

Can't find a part number for the actual gear though.

Are parts still readily available for the EGX-20?

Re: EGX-20 Table Issue

Posted: Wed Oct 11, 2017 12:47 pm
by Kai Perry
The gear has two parts, with two part numbers -

21685141 (Upper) & 21685142 (Lower)

Re: EGX-20 Table Issue

Posted: Thu Oct 12, 2017 10:42 am
by antelopeslr5000
Thank you very much Kai, greatly appreciated!