Search found 8 matches

by stiks
Sun Jan 14, 2018 6:48 pm
Forum: 3D Prototyping & Milling
Topic: Roland MDX-40A spindle problem
Replies: 5
Views: 338

Re: Roland MDX-40A spindle problem

Sorry we do not give our service manuals and those notes are not ours, we would not suggest using a paper clip. :) For service issues we prefer you contact our support team. Our UK support is here :- https://www.rolanddg.co.uk/support/log-a-case (if you are not in the UK then please contact your lo...
by stiks
Sun Jan 14, 2018 5:43 pm
Forum: 3D Prototyping & Milling
Topic: Roland MDX-40A spindle problem
Replies: 5
Views: 338

Re: Roland MDX-40A spindle problem

I found several photos of myself. Where can they be from?
MVC-168F.JPG
by stiks
Sun Jan 14, 2018 5:21 pm
Forum: 3D Prototyping & Milling
Topic: Roland MDX-40A spindle problem
Replies: 5
Views: 338

Re: Roland MDX-40A spindle problem

Hello Yes the MDX-40 spindle is under spring pressure, so there is a small movement if you press the spindle down from the top. As it pops up, that is OK. Many thanks, Patrick. I changed the bearings in the spindle. The problem with the bands did not dare. The next step is to check the collet and t...
by stiks
Tue Jan 09, 2018 8:57 pm
Forum: 3D Prototyping & Milling
Topic: Roland MDX-40A spindle problem
Replies: 5
Views: 338

Roland MDX-40A spindle problem

Hello. I have problems with my machine. When I press the spindle, it drops about 1 mm. Then comes back. Should it be so? Maybe I should tighten the nut?
Strips appeared on the surface of the parts, I was looking for the cause.
Thank you in advance.
12893cf0-cba1-46c6-b8f7-8d53babb57cc.JPG
by stiks
Thu Dec 18, 2014 1:05 pm
Forum: 3D Prototyping & Milling
Topic: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a problem
Replies: 18
Views: 5854

Re: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a proble

I do not use SRP Player. Only Deskproto and RhinoCam. But the problem is not in the program because the offset is present during manual operation. Tell me, how often to set up the origins? Before, I did it in front of each cutting for good accuracy. It seems to me that this is not correct. Now reboo...
by stiks
Sun Dec 14, 2014 11:24 am
Forum: 3D Prototyping & Milling
Topic: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a problem
Replies: 18
Views: 5854

Re: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a proble

Hi again. The problem was not solved. During attempts found that displacement occurs during the detection jig. But not always. Tell me, what else could be the reason? Also 2 times there was an error. Thank U. http://i.piccy.info/i9/a85632530866df65d202d376bfefa2ee/1418552666/8366/842539/1_240.jpg ht...
by stiks
Fri Dec 05, 2014 8:03 am
Forum: 3D Prototyping & Milling
Topic: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a problem
Replies: 18
Views: 5854

Re: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a proble

Hello. Thanks for the reply.
I greased the rails and pulled the gear. The problem was with poor grounding.
Thx
by stiks
Sat Nov 22, 2014 9:07 am
Forum: 3D Prototyping & Milling
Topic: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a problem
Replies: 18
Views: 5854

Re: Newbie with MDX-40a and Rotary Axis Unit ZCL-40a proble

Hello. I have a problem with my Roland MDX40A and ZCL-40A This machine for about four years. There are problems with the Y axis. By turning the y coordinate shifts. Each time a new value. Tried calibration correction settings. But the importance of constantly different. Disassemble axis, check the b...