Need advice on using your Roland Hardware.
Please note we do not give engineering advice in this group
-
mrtn
- Gold Member
- Posts: 2519
- Joined: Tue Feb 14, 2012 4:37 pm
- Location: Tallinn, Estonia
Post
by mrtn » Tue Mar 21, 2017 1:38 am
Other than the whole thing looks like a train wreck?
No. Anything from the cartridge bay to the pump. Most likely captop/head/manifold/damper/tubing. I think I have already told this.
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Thu Mar 23, 2017 9:08 pm
What is the part number for the 8 tubs that come off the dampers? and what is the part number for the Y-shaped splitters they connect too?
is the spec on the pipe size and material wise so iI could maybe source it from a hardware store?
-
mrtn
- Gold Member
- Posts: 2519
- Joined: Tue Feb 14, 2012 4:37 pm
- Location: Tallinn, Estonia
Post
by mrtn » Thu Mar 23, 2017 10:51 pm
There are no measurements in the manuals, you could just measure it and go check a special store, don't rely on home depot, theirs may not be solvent resistant.
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Sat Mar 25, 2017 9:05 pm
Possibility sirted with check for air tomorrow
But what's this black haze/mist?
-
Attachments
-

-
mrtn
- Gold Member
- Posts: 2519
- Joined: Tue Feb 14, 2012 4:37 pm
- Location: Tallinn, Estonia
Post
by mrtn » Sat Mar 25, 2017 10:48 pm
Very likely a hair or something else causing a deflected nozzle. Check with a good lamp.
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Sun Mar 26, 2017 11:07 am
interesting i will look for one shortly, does the image look like its put down too much ink ? e.i. wrong profile?
-
mrtn
- Gold Member
- Posts: 2519
- Joined: Tue Feb 14, 2012 4:37 pm
- Location: Tallinn, Estonia
Post
by mrtn » Sun Mar 26, 2017 2:54 pm
Perhaps a tiny bit. Try lowering the ink limit.
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Sun Mar 26, 2017 4:54 pm
How do I do that!?
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Sun Mar 26, 2017 4:57 pm
Should heater setting be set to "use printer setting" or "use default media settings"?
-
itfben
- Bronze Member
- Posts: 75
- Joined: Tue Jun 14, 2016 10:34 am
-
Contact:
Post
by itfben » Sun Mar 26, 2017 4:59 pm
In the colour managment section at the bottom of quality settings in VW should I have "specify profile and ignore default" ticked or untucked if using a profile supplied to my by All Print Supplies to my LG media?
Who is online
Users browsing this forum: No registered users and 1 guest