
RotoCAMM TS-400E
Re: RotoCAMM TS-400E
When it's working properly it gives out 36V adjustable with pot. When it decides to pack in it swings between 2 and 9v - pretty flaky/unreliable 

Hardware: TS-400 which seems to be the same as an EGX-400/600...
-
- Bronze Member
- Posts: 85
- Joined: Sun Sep 18, 2011 11:41 am
- Location: North Lincolnshire
Re: RotoCAMM TS-400E
Could be a dry joint, might be worth going over every joint on the board with a soldering iron.
Richard
Richard
If it was all as easy as it looked!!!!!!!!!
Re: RotoCAMM TS-400E
For the sake of £36 - I'm giving up looking now. Wish I had just bought a new power supply a month ago
All a learning experience I suppose...

All a learning experience I suppose...
Hardware: TS-400 which seems to be the same as an EGX-400/600...
-
- Bronze Member
- Posts: 85
- Joined: Sun Sep 18, 2011 11:41 am
- Location: North Lincolnshire
Re: RotoCAMM TS-400E
A fair comment. Well if you're throwing it away, please throw it my way!
Richard

Richard
If it was all as easy as it looked!!!!!!!!!
Re: RotoCAMM TS-400E
I'll keep you in mind 

Hardware: TS-400 which seems to be the same as an EGX-400/600...
Re: RotoCAMM TS-400E
It's ALIVE
Just had a quick play with it and so far so good. HAPPY (if a bit rainy) DAYS!!


Just had a quick play with it and so far so good. HAPPY (if a bit rainy) DAYS!!

Hardware: TS-400 which seems to be the same as an EGX-400/600...
-
- Bronze Member
- Posts: 85
- Joined: Sun Sep 18, 2011 11:41 am
- Location: North Lincolnshire
Re: RotoCAMM TS-400E
Hi Paul,
Excellent, well done! Hopefully it should be fine now.
Regards
Richard
Excellent, well done! Hopefully it should be fine now.
Regards
Richard
If it was all as easy as it looked!!!!!!!!!
Re: RotoCAMM TS-400E
Well - the day has finally come… I think the machine is dead
It mostly works fine but when I try and write a new parameter in VPanel - a new home or Z position for instance - Vpanel just freezes up. Not the computer as tried old laptop too. Will dig out a new USB lead tomorrow but I'm not hopeful.
I can move it around and the hand control still works.
Any ideas?
Just when it's been running great too. On top of all that - I'm on the final cut of a two week project!!
Time for a VERY large dram...

It mostly works fine but when I try and write a new parameter in VPanel - a new home or Z position for instance - Vpanel just freezes up. Not the computer as tried old laptop too. Will dig out a new USB lead tomorrow but I'm not hopeful.
I can move it around and the hand control still works.
Any ideas?
Just when it's been running great too. On top of all that - I'm on the final cut of a two week project!!
Time for a VERY large dram...
Re: RotoCAMM TS-400E
It lives again! Literally gave it blood offering and managed to get the fianl piece finished. Worth a very nippy thumb
Really weird. It could do everything - including outputting a toolpath - but would freeze when trying to set a new home position.
Time will tell if this is a one off anomaly...

Really weird. It could do everything - including outputting a toolpath - but would freeze when trying to set a new home position.
Time will tell if this is a one off anomaly...
Hardware: TS-400 which seems to be the same as an EGX-400/600...
Re: RotoCAMM TS-400E
Hi, I have the minimum knowledge of cnc machines except for some basic work on the camm 2,
I have acquired a ts-400, I have got it set up, but vpannel is saying emergency stop on? The emergency stop on the machine seems loose but working! Do you think it could be this?
I have acquired a ts-400, I have got it set up, but vpannel is saying emergency stop on? The emergency stop on the machine seems loose but working! Do you think it could be this?
Who is online
Users browsing this forum: No registered users and 2 guests